Active Harmonic Filter AHF 100A 440V Port Crane Cabinet for Shore Power Harmonic Reduction

ND-AHF-100-440-C is a floor standing cabinet rated 100 A at 440 V AC (3P4W) built for port and terminal operations. It removes harmonic current at the point where the non-linear load connects, so the distortion stops at the source instead of spreading through upstream switchgear, transformers and generators.

Crane drives and shore power converters run at 440V, so the filter is installed downstream of the main breaker where the crane feeder meets the terminal board.

The unit measures the load current continuously and injects an equal and opposite compensation current, so the grid current returns to a near sinusoidal shape while the load keeps running unchanged. Reactive power compensation and three-phase unbalance correction can be enabled on the same hardware, which means one Active Harmonic Filter AHF can replace a combination of capacitor banks, detuned reactors and balancing equipment.

Main technical characteristics of this 100 A 440 V Active Harmonic Filter AHF:

• PCB Anti-Corrosion Coating
  Conformal coating resists humidity, dust and corrosive mist in coastal and heavy-industry environments.
• Wide Ambient Envelope
  Operation from -25 to +60 degrees C with high humidity tolerance; derating applies only above 2000 m altitude.
• Complete Internal Protection Chain
  Over-voltage, under-voltage, over-current, over-temperature, phase-loss and short-circuit protection act without external relays.
• Selectable Compensation Modes
  Harmonic filtering, reactive power compensation and three-phase balancing can be enabled separately or together from one menu.
• Parallel Expansion up to Ten Units
  Up to ten units share one CT signal, so capacity grows with the plant and N+1 redundancy becomes possible.
• Modular Plug-in Architecture
  Power modules slide in and out for maintenance, cutting mean time to repair during planned shutdowns.
• Closed Forced Ventilation Duct
  Heat sources sit inside a dedicated duct, separated from dust-prone areas, so the internal temperature of the enclosure stays low.
• RS485 Modbus Reporting
  Standard Modbus-RTU output lets the filter report into a BMS, SCADA or energy management platform.

This Active Harmonic Filter AHF is normally installed on the following loads:

• Ship to shore crane drives
• Reefer container power stacks
• Shore power and cold ironing systems
• Terminal yard crane rectifiers
• Conveyor and bulk handling drives

Reasons buyers select our Active Harmonic Filter AHF for projects in port and terminal operations:

• Export Track Record
  We work with energy engineering distributors across Southeast Asia, the Middle East, Europe, America and Africa, with core cooperation in India, Germany and Saudi Arabia.
• Manufacturer Scope
  We are a Shanghai based power quality manufacturer with our own R and D labs, production workshops and a full-function test bay, so the algorithms, firmware, hardware and cabinet structure are all developed in house.
• Selection and Survey Support
  Our engineers review your harmonic measurement, calculate the required compensation current and issue a written selection report before you place an order.
• Full-Load Aging before Packing
  Every Active Harmonic Filter AHF runs a 24-hour full-load aging cycle and is inspected against its test record before shipment.
• Project-Specific Engineering
  Capacity, voltage class, CT ratio, cabinet colour and communication protocol are configured against your single line diagram instead of being taken from a catalogue page.

Typical configuration of model ND-AHF-100-440-C. Voltage class, current rating, CT ratio and enclosure can be adapted to your single line diagram.

Common questions about this Active Harmonic Filter AHF from project engineers and distributors:

Nengdu New Energy is a Shanghai based high-tech manufacturer focused on integrated research, production, sales and after-sales service of power quality improvement equipment. The product line covers AHF active filters, SVG static var generators, intelligent capacitors, reactive power controllers, capacitor contactors, voltage adjusters, smart composite switches, dynamic reactive regulators and matching energy storage systems.

Standardised production workshops, dedicated R and D laboratories and a full-function testing workshop support in-house development of every algorithm, software, hardware platform and cabinet structure. Customised power equipment and complete turnkey solutions are supplied, and ODM cooperation is available for partners who need their own branding.

Products hold CE, IEC, RoHS and ISO certification. Long-term partnerships with energy engineering distributors span Southeast Asia, the Middle East, Europe, America and Africa, with core cooperation in India, Germany and Saudi Arabia. Our engineering team provides on-site power quality testing and calculation, equipment replacement matching, programming and commissioning guidance, plus permanent remote after-sales assistance.

• Technical Support
  Lifetime free remote technical support for commissioning, troubleshooting and parameter configuration by video call, WhatsApp or email.
• Training Materials
  Complete operation manuals, wiring diagrams and parameter explanations are supplied so your engineers can run the unit independently.
• On-Site Service
  Where overseas on-site commissioning is required, engineers can be dispatched abroad; travel and service fees are quoted separately.
• Warranty
  A limited warranty applies, with the specific period and terms confirmed in the project contract.
• Response Time
  After-sales and technical enquiries are answered within 24 working hours.
• Spare Parts Supply
  After the warranty period, spare parts are supplied at reasonable cost for the full service life of the equipment.

Send us your single line diagram, harmonic measurement or load list, and our engineers will calculate the required compensation current and confirm the matching Active Harmonic Filter AHF model for your site. Typical response time is within 24 working hours.