Active Harmonic Filter AHF 125A 400V Rack Module for EV Charging Hub Harmonic Control

ND-AHF-125-400-R is a 19 inch rack module rated 125 A at 400 V AC (3P4W) built for EV charging hubs. It removes harmonic current at the point where the non-linear load connects, so the distortion stops at the source instead of spreading through upstream switchgear, transformers and generators.

Charging hubs switch load in and out all day, so the module is specified for repeated step changes instead of a steady industrial duty cycle.

The unit measures the load current continuously and injects an equal and opposite compensation current, so the grid current returns to a near sinusoidal shape while the load keeps running unchanged. Reactive power compensation and three-phase unbalance correction can be enabled on the same hardware, which means one Active Harmonic Filter AHF can replace a combination of capacitor banks, detuned reactors and balancing equipment.

Main technical characteristics of this 125 A 400 V Active Harmonic Filter AHF:

• Fast Dynamic Tracking
  Detection happens within microseconds, so compensation follows welding, crane and press loads that change cycle by cycle.
• Parallel Expansion up to Ten Units
  Up to ten units share one CT signal, so capacity grows with the plant and N+1 redundancy becomes possible.
• 2nd to 50th Harmonic Selection
  Individual harmonic orders can be enabled or blocked, so only the orders that actually exist in the network are compensated.
• Two Sets of External CT Terminals
  Both CT input sets can be assigned to different feeders, which simplifies retrofit wiring inside existing switchgear.
• Front-Access Service Design
  Terminals, fans and modules are reachable from the front, so maintenance does not need side clearance.
• Integrated HMI with Event Log
  The LCD panel shows voltage, current, THDi, power factor and module status, with event records for fast diagnosis.
• 24-Hour Full-Load Aging Run
  Every unit completes a full-load burn-in before packing, so early failures are screened at the factory rather than at your site.
• Selectable Compensation Modes
  Harmonic filtering, reactive power compensation and three-phase balancing can be enabled separately or together from one menu.

This Active Harmonic Filter AHF is normally installed on the following loads:

• DC fast charging hubs and depots
• AC destination charging car parks
• Fleet charging with mixed charger brands
• Charging sites sharing a small transformer
• Highway service areas with step load switching

Reasons buyers select our Active Harmonic Filter AHF for projects in EV charging hubs:

• Project-Specific Engineering
  Capacity, voltage class, CT ratio, cabinet colour and communication protocol are configured against your single line diagram instead of being taken from a catalogue page.
• OEM and ODM Cooperation
  Private label panels, custom enclosure dimensions and customised display languages are available for distributors and system integrators.
• Response within 24 Working Hours
  Technical and commercial questions are answered within one working day, and remote commissioning runs over video call, email or WhatsApp.
• Spare Parts after Warranty
  Fans, control boards, CTs and power modules remain available at reasonable cost once the warranty period ends.
• Full-Load Aging before Packing
  Every Active Harmonic Filter AHF runs a 24-hour full-load aging cycle and is inspected against its test record before shipment.

Typical configuration of model ND-AHF-125-400-R. Voltage class, current rating, CT ratio and enclosure can be adapted to your single line diagram.

Common questions about this Active Harmonic Filter AHF from project engineers and distributors:

Nengdu New Energy is a Shanghai based high-tech manufacturer focused on integrated research, production, sales and after-sales service of power quality improvement equipment. The product line covers AHF active filters, SVG static var generators, intelligent capacitors, reactive power controllers, capacitor contactors, voltage adjusters, smart composite switches, dynamic reactive regulators and matching energy storage systems.

Standardised production workshops, dedicated R and D laboratories and a full-function testing workshop support in-house development of every algorithm, software, hardware platform and cabinet structure. Customised power equipment and complete turnkey solutions are supplied, and ODM cooperation is available for partners who need their own branding.

Products hold CE, IEC, RoHS and ISO certification. Long-term partnerships with energy engineering distributors span Southeast Asia, the Middle East, Europe, America and Africa, with core cooperation in India, Germany and Saudi Arabia. Our engineering team provides on-site power quality testing and calculation, equipment replacement matching, programming and commissioning guidance, plus permanent remote after-sales assistance.

• Technical Support
  Lifetime free remote technical support for commissioning, troubleshooting and parameter configuration by video call, WhatsApp or email.
• Training Materials
  Complete operation manuals, wiring diagrams and parameter explanations are supplied so your engineers can run the unit independently.
• On-Site Service
  Where overseas on-site commissioning is required, engineers can be dispatched abroad; travel and service fees are quoted separately.
• Warranty
  A limited warranty applies, with the specific period and terms confirmed in the project contract.
• Response Time
  After-sales and technical enquiries are answered within 24 working hours.
• Spare Parts Supply
  After the warranty period, spare parts are supplied at reasonable cost for the full service life of the equipment.

Send us your single line diagram, harmonic measurement or load list, and our engineers will calculate the required compensation current and confirm the matching Active Harmonic Filter AHF model for your site. Typical response time is within 24 working hours.